Search found 10 matches

If I predate an article, I think the article should post immediately, but it sits in "programmed articles" for a couple of days, then posts. Someone else said it doesn't post at all for him/her:
http ...

well, I had to wait a couple days for the predated programmed article to finally post. I was only predating a few days, though. Of course, I think if you predate, the article should post immediately. ...

Cyberkiller:

if you do a fresh install, it would be great if you could test it out before you do any edits.

1. test the predating problem
2. test to see if editing a programmed article changes ...

I'm using raven7.6v2.02.

I just had another article programmed for 1/21 (I programmed it on 1/22) that finally posted around midnight last night. Of course, as mentioned, because I edited it, the t ...

Cyberkiller:

Have you tried letting the articles just sit in programmed articles for a few days? I noticed with the few I've done, that after a few days past the programmed date, it will post event ...

I changed my timezone by modifying theme.php

just added
putenv("TZ=YOUR_TIMEZONE_HERE");

at the beginning (after <?php ) of theme.php

Some different TZ's are here: http://www.timezonecon ...

I also want to pre-date articles, and they do sit in the "Programmed Articles" for a couple days, but then they somehow are allowed out into "Last 20 Articles" after that. I'm not sure why it does tha ...

It does not sound like you were able to set your CGI up correctly. Start over with a fresh .htaccess that came with the download. That will allow you back into your admin functions. When you use th ...

Well, I continued on, then got to the
*Configure NukeSentinel(tm)* step, which starts with:

"Make sure that you have completed the Base RavenNuke76(tm) Configuration and the Forum Configuration ...

Aloha all!

I got to the INSTALLATION/installSQL.php step, and since I got no response from Step 4 (Load All IP2COUNTRY Data), tried the steps 4a-4f, starting with 4a, but I wasn't getting a respons ...

Author	Message
Topic: predated programmed articles not posting
kaimuki Replies: 18 Views: 25715	Forum: phpnuke 7.6 Bugs/Fixes Posted: Sun Jan 29, 2006 1:56 am Subject: predated programmed articles not posting
kaimuki Replies: 18 Views: 25715	If I predate an article, I think the article should post immediately, but it sits in "programmed articles" for a couple of days, then posts. Someone else said it doesn't post at all for him/her: http ...
Topic: Can't predate news posts
kaimuki Replies: 13 Views: 18476	Forum: phpnuke 7.6 Posted: Tue Jan 24, 2006 10:49 pm Subject: Can't predate news posts
kaimuki Replies: 13 Views: 18476	well, I had to wait a couple days for the predated programmed article to finally post. I was only predating a few days, though. Of course, I think if you predate, the article should post immediately. ...
Topic: Can't predate news posts
kaimuki Replies: 13 Views: 18476	Forum: phpnuke 7.6 Posted: Tue Jan 24, 2006 4:29 pm Subject: Can't predate news posts
kaimuki Replies: 13 Views: 18476	Cyberkiller: if you do a fresh install, it would be great if you could test it out before you do any edits. 1. test the predating problem 2. test to see if editing a programmed article changes ...
Topic: Can't predate news posts
kaimuki Replies: 13 Views: 18476	Forum: phpnuke 7.6 Posted: Tue Jan 24, 2006 1:53 pm Subject: Can't predate news posts
kaimuki Replies: 13 Views: 18476	I'm using raven7.6v2.02. I just had another article programmed for 1/21 (I programmed it on 1/22) that finally posted around midnight last night. Of course, as mentioned, because I edited it, the t ...
Topic: Can't predate news posts
kaimuki Replies: 13 Views: 18476	Forum: phpnuke 7.6 Posted: Tue Jan 24, 2006 12:37 am Subject: Can't predate news posts
kaimuki Replies: 13 Views: 18476	Cyberkiller: Have you tried letting the articles just sit in programmed articles for a few days? I noticed with the few I've done, that after a few days past the programmed date, it will post event ...
Topic: CET to GMT
kaimuki Replies: 7 Views: 9456	Forum: phpnuke 7.6 Posted: Mon Jan 23, 2006 11:33 pm Subject: CET to GMT
kaimuki Replies: 7 Views: 9456	I changed my timezone by modifying theme.php just added putenv("TZ=YOUR_TIMEZONE_HERE"); at the beginning (after <?php ) of theme.php Some different TZ's are here: http://www.timezonecon ...
Topic: Can't predate news posts
kaimuki Replies: 13 Views: 18476	Forum: phpnuke 7.6 Posted: Mon Jan 23, 2006 11:09 pm Subject: Can't predate news posts
kaimuki Replies: 13 Views: 18476	I also want to pre-date articles, and they do sit in the "Programmed Articles" for a couple days, but then they somehow are allowed out into "Last 20 Articles" after that. I'm not sure why it does tha ...
Topic: Admin Sign On problem
kaimuki Replies: 14 Views: 20608	Forum: Raven's RavenNuke(tm) v2.00.00 - v2.02.00 Distro Posted: Mon Jan 09, 2006 2:51 am Subject: Re: Admin Sign On problem
kaimuki Replies: 14 Views: 20608	It does not sound like you were able to set your CGI up correctly. Start over with a fresh .htaccess that came with the download. That will allow you back into your admin functions. When you use th ...
Topic: IP2COUNTRY installSQL.php problem?
kaimuki Replies: 3 Views: 11380	Forum: Raven's RavenNuke(tm) v2.00.00 - v2.02.00 Distro Posted: Sun Jan 08, 2006 4:15 am Subject: IP2COUNTRY installSQL.php problem?
kaimuki Replies: 3 Views: 11380	Well, I continued on, then got to the Configure NukeSentinel(tm) step, which starts with: "Make sure that you have completed the Base RavenNuke76(tm) Configuration and the Forum Configuration ...
Topic: IP2COUNTRY installSQL.php problem?
kaimuki Replies: 3 Views: 11380	Forum: Raven's RavenNuke(tm) v2.00.00 - v2.02.00 Distro Posted: Sun Jan 08, 2006 3:26 am Subject: IP2COUNTRY installSQL.php problem?
kaimuki Replies: 3 Views: 11380	Aloha all! I got to the INSTALLATION/installSQL.php step, and since I got no response from Step 4 (Load All IP2COUNTRY Data), tried the steps 4a-4f, starting with 4a, but I wasn't getting a respons ...